By ShowMeStepByStepPublished
Based on a video by Create with Karen Elaine.
This paper Christmas tree folds from a single square, stands up on the table by itself, and still lies flat enough to slip inside a greeting card. Karen Elaine of Create with Karen Elaine walks through every fold on a larger sheet so you can see what the paper is doing. The design comes from the Craftaholic Witch, whose origami Christmas tree tutorial Karen credits as the original, and it is worth a look if you want a second angle on the tricky middle fold.
You need one square of paper, a scrap of silver or gold paper for the star, a dab of glue, and a marker or two. A bone folder helps a lot. Plan on about fifteen minutes for your first tree and five once the folds make sense.
Standard 6 inch origami paper makes a tree about 4 inches tall, which is the right size for a card or a place setting. Karen demonstrates with 8.5 inch scrapbook paper so the folds are easy to see. It works, but it gets thick in the later steps. Thin paper folds cleaner, so if you are buying some, get kami or duo paper rather than cardstock.
Colour matters more than you might think. The white back of the sheet becomes the trunk and the little base, so a paper that is green on one side and white on the other gives you a two-tone tree with no extra work. Patterned scrapbook paper in a tiny print looks great too. Big prints get lost in the pleats.
The pleats you make in the middle of the fold give the tree a slight 3D shape, and the two flaps you fold out at the very end act as feet. Open them to about the same angle and the tree stands. Fold them flat and it goes into an envelope. If it tips over, the flaps are uneven. Line them up and give the base another crease.
Karen says it herself: the inside fold in step five is the one that trips people up. You are not making any new creases there. Every fold already exists from the earlier steps, and you are only telling the paper which way to go. Open the layer, find the valley crease, and let the paper fall into it. If you find yourself pressing a new line into the paper, stop, unfold, and look for the existing crease instead.
Sharp creases in the early steps make this part far easier. Run a bone folder or the back of a fingernail along every fold before moving on.
A hand cut star has charm, but a star paper punch gives you a clean one in a second. Try glitter cardstock or foil paper for the star. For the branches, draw small scallops across each pleat to look like garland, or dot the tree with a white paint pen for snow. Write a guest name on the trunk and you have a place card for the holiday table.
Pair a few trees with a paper star or a string of paper snowflakes for a table display. Tuck one inside a handmade card, or glue a small one to Christmas gift tags. New to folding? Start with the basics in how to make origami.
10 steps · about 11 minutes.Check off each step as you go and your progress saves automatically.
Lay the paper colour side up. Fold one corner over to the opposite corner to make a triangle and crease it hard. Open it, turn the paper a quarter turn, and fold the other two corners together the same way. When you open it up you should see an X of creases across the square.
Tip
Line the points up exactly before you crease. A small miss here turns into a lopsided tree later.
Flip the sheet so the colour side is down. Fold it in half like a book, making sure the edges meet, and crease. Open it and fold it in half the other direction. You now have a plus sign of creases on top of the X from step one, four crease lines crossing in the middle.
Tip
These two folds go the opposite way to the diagonals. That is what lets the paper collapse in the next step.
Pick the paper up and push the sides in along the creases you made. It folds down into a smaller square with two flaps on each side. No new folds are needed. Press it flat with the open end pointing toward you. It should look like a small diamond once you turn it.
Tip
If it will not collapse, one of the creases is going the wrong way. Refold it in the other direction and try again.
Take the folded edge on one side of the top layer and fold it in to the center line. Do the same on the other side. Keep the open edge at the bottom. Then fold each side in to the center once more to make a long, narrow point. It gets thick, so press each crease firmly.
Tip
A bone folder is worth having for this step. Fingers alone leave soft creases that make step five harder.
Open one side back up. Using the creases already there, fold the outer section over and tuck it in between the layers, then lay it flat. You will see the pleats of the tree start to appear. Repeat on the other side of the front. Karen calls this the hardest part, so go slowly.
Tip
Do not make new creases here. If the paper resists, you are fighting the existing folds. Open it and look again.
Turn the tree over. Fold both edges to the center, then fold them to the center again, the same as the front. Open each side, lift the flap, and tuck it under on the existing creases so the back matches the front. Both sides should now look the same, with matching pleats on each face.
Tip
The back is easier than the front because your hands already know the move.
Fold the bottom layer up so it runs straight across and crease it. Repeat on the other side so the two little corners meet at a point. Then reverse both of those folds by folding them back the other way. The white section showing at the bottom is the trunk.
Tip
Get this line as level as you can. A crooked fold here shows as a leaning trunk.
There is still some loose paper below the tree. Fold that raw section up until it lines up with the bottom of the tree, crease it, then reverse the fold and tuck it inside. Do the other side the same way. Fold the two flaps back out so they are even. Those are the feet your tree stands on.
Tip
Open the two feet to the same angle before you stand it up.
Cut two small stars from silver or gold paper, or punch them out. Put a little glue on the back of one star and press it behind the tip of the tree so it sticks out the top. Glue the second star to the front, lined up with the first, so the star looks right from both sides.
Tip
Use a glue with a fine tip. A thin line holds and does not soak through the paper.
Take a green marker and draw rows of small scallops across the tree, using the pleats as your guide. Karen does three little curves per row. Go over them with a silver marker if you want the garland to stand out more. Decorate the back too, since the tree is seen from both sides.
Tip
Acrylic paint markers show up on dark green paper far better than felt tips.
Keep going
How to Make a Paper Turkey
How to Make a Paper Christmas Tree
E6000
E6000 Craft Adhesive, Clear (3.7 oz)
The industrial-strength craft glue that bonds glass, wood, ceramic, metal, fabric, and concrete. The one adhesive most craft projects reach for.
Gorilla
Gorilla Dual-Temp Full-Size Hot Glue Gun
Dual-temp so it handles delicate florals and heavy materials alike. A precise nozzle and built-in stand make it the everyday craft-table gun.
OLFA
OLFA 18" x 24" Self-Healing Cutting Mat
The pro-standard cutting surface. Gridlines for square cuts, self-healing so blades never leave grooves, and big enough for paper, fabric, and leather.
As an Amazon Associate we earn from qualifying purchases. Links on this page may be affiliate links - clicking them and buying doesn't change your price, but helps support ShowMeStepByStep.
Sunday How-To
One short email with the week's best step-by-step guides. Free, no spam, unsubscribe anytime.
Did this work for you?
Curated theme pages that include this tutorial.
Hand-picked next reads based on the one you just finished.
Pick the categories you want to hear about. Weekly digest of new step-by-step tutorials. No spam, easy unsubscribe.
Send me tutorials about
