How to Make a Clay Candle Holder

PotteryEasy5:1510 stepsPart of Crafting for BeginnersBrowse more →
The finished result: How to Make a Clay Candle Holder

By Show Me Step by StepPublished

Based on a video by Crockd.

A small clay candle holder for a taper candle is one of the best first hand-building projects. It uses two basic skills, a slab and a coil, and finishes in an afternoon. This tutorial follows Montana from Crockd, who builds a little holder with a round base, a cup for the candle and a loop handle, using only a few wooden tools and a bowl of water.

How to make a clay candle holder: the short version

  • Roll a slab about a quarter inch thick and cut a circle for the base.
  • Cut a rectangle, roll it into a cup the width of your candle, and join the seam.
  • Roll a coil for the handle and attach it.
  • Join the cup to the base and blend a coil over the seam.
  • Smooth it, let it dry, then paint or fire it.

Air dry clay or kiln clay

Crockd says you do not need a kiln. Air dry clay hardens on its own in a day or two, and you can paint it with acrylics afterward. It is decorative only. It is not waterproof and it is softer than fired clay. If you have a local studio that fires pieces, use a stoneware or earthenware clay instead and you get a harder, glazed finish. Carve your initials in the bottom so the studio knows it is yours.

Sizing the candle cup

Standard taper candles are about 7/8 inch across at the base. Wrap your clay rectangle around a candle, or a marker of the same width, to size the cup. Make it a little snug. Air dry clay shrinks slightly as it dries, and a candle that wobbles is unsafe. A cup about an inch deep holds a taper upright.

Why score and slip every join

Clay pieces do not stick to each other by pressing alone. Scratch both surfaces with little hash marks, dab them with water or slip, then press together and blend. The thin coils Montana adds around the handle and the base are extra glue. They fill the seam and stop cracks forming as it dries.

Drying and finishing

  • Dry slowly, away from heaters, loosely covered with plastic for the first day.
  • Turn it now and then so the base dries evenly and does not curl.
  • Sand rough spots lightly once it is bone dry.
  • Paint with acrylics, then seal with a matte varnish for a soft stone look.

Ways to change the design

  • Cut the base as a square, a scalloped flower or a little dish that catches drips.
  • Skip the handle and make the cup taller for a simple candlestick.
  • Press lace or a leaf into the slab before cutting for texture.
  • Make a pair in two heights for a mantel or a dinner table.

Common problems

  • Handle cracks off. The join was not scored, or it dried too fast. Score, wet and add a reinforcing coil.
  • Base curls up. It dried faster than the cup. Cover it loosely and turn it while drying.
  • Candle wobbles. The cup is too wide. Wrap a little poster putty around the candle base.

Candle safety

Use it with a real flame only if it holds the candle firmly and sits flat. Keep it away from anything that can catch, and never leave a lit candle alone. LED tapers are a good choice for air dry pieces and for homes with kids or pets.

More clay projects

Learn the join in detail in how to score and slip clay. Practise coils with a coil pot, try a slab mug next, or read how to use air dry clay.

What you'll need

Step-by-Step Guide

10 steps · about 5 minutes.Check off each step as you go and your progress saves automatically.

1

Roll the Clay Into a Flat Slab for the Candle Holder

1:00
Step 1: Roll the Clay Into a Flat Slab for the Candle Holder - How to Make a Clay Candle Holder

Tear off about a quarter of your clay and put the rest back in the bag so it does not dry out. Warm the clay by slapping it between your palms, then roll it into a ball. Flatten it with your hand and roll it into a smooth slab. A rolling pin or a glass jar works. Aim for about a quarter inch thick, so it is sturdy but not heavy.

Tip

Lay two paint stirrers either side of the clay and roll over them for an even thickness.

2

Cut a Round Clay Base for the Candle Holder

1:10
Step 2: Cut a Round Clay Base for the Candle Holder - How to Make a Clay Candle Holder

Once the slab is smooth and even, cut out the base. It can be any shape. Montana goes with a circle. Trace around a lid or a cup with a wooden tool or a needle tool, then lift away the extra clay. Keep the scraps wrapped up. You will need them for the cup, the handle and the small coils later.

Tip

Smooth the cut edge with a damp finger so it does not crack as it dries.

3

Roll a Clay Rectangle Into the Candle Cup Cylinder

2:00
Step 3: Roll a Clay Rectangle Into the Candle Cup Cylinder - How to Make a Clay Candle Holder

Roll a second slab and cut a rectangle for the cup that holds the candle. Roll it into a cylinder to check the size. It should fit a taper candle snugly. Trim off the extra clay where the ends overlap. You can taper the ends slightly so the seam sits flatter when you join them.

Tip

Wrap the rectangle around a candle or a marker to size the cup exactly.

4

Score the Clay Edges Where the Cylinder Seam Joins

2:12
Step 4: Score the Clay Edges Where the Cylinder Seam Joins - How to Make a Clay Candle Holder

Unroll the rectangle. Use a spiky scoring tool to draw little x's or hash marks along one end. Flip the piece over and score the other end on the opposite side. Dab both scored areas with water. This roughs up the surface so the two edges grip each other instead of sliding apart.

Tip

A fork works if you do not have a scoring tool.

5

Blend the Seam on the Clay Candle Cup

2:27
Step 5: Blend the Seam on the Clay Candle Cup - How to Make a Clay Candle Holder

Roll the rectangle back into a cylinder, pressing the scored ends together. Use a wooden spoon-shaped tool to drag clay across the join, first one way, then the other, until you cannot see a line. Support the inside with a finger while you work so the cup keeps its round shape.

Tip

Blend on the outside and the inside. A seam left on one side can split as it dries.

6

Roll a Clay Coil for the Candle Holder Handle

2:52
Step 6: Roll a Clay Coil for the Candle Holder Handle - How to Make a Clay Candle Holder

Grab a small chunk of clay and roll it into a ball. Then roll the ball back and forth under your fingers, on the board or between your hands, until it becomes a long, even coil. Trim the ends and bend it into a loop for the handle. You can put the handle on the cup or on the base, whichever you like.

Tip

Keep your fingers spread and move from the middle outward for an even coil.

7

Attach the Clay Coil Handle to the Candle Cup

3:08
Step 7: Attach the Clay Coil Handle to the Candle Cup - How to Make a Clay Candle Holder

Score both ends of the handle and the spots on the cup where they will join. Dab the scored areas with water. Press the handle on and blend each end into the cup with the wooden tool. Hold the loop gently while you blend so it keeps its shape and does not flatten against the side.

Tip

Make the handle big enough to fit a finger through.

8

Reinforce the Clay Handle Joints With a Thin Coil

3:46
Step 8: Reinforce the Clay Handle Joints With a Thin Coil - How to Make a Clay Candle Holder

For extra strength, roll out a tiny coil. Wrap it tightly around each point where the handle meets the cup. Then blend the coil into both the handle and the cup with the tool or a fingertip. It fills the gap at the joint and stops the handle from cracking off as the clay dries.

Tip

Dip the tool in water now and then to smooth the clay more easily.

9

Score the Bottom of the Clay Candle Cup to Attach the Base

4:02
Step 9: Score the Bottom of the Clay Candle Cup to Attach the Base - How to Make a Clay Candle Holder

Now join the cup to the base. Score the bottom rim of the cup and the spot on the base where it will sit. Dab both with water. Press the cup down firmly onto the base. Check it from the side to make sure it stands straight, or the candle will lean.

Tip

Set it toward the middle of the base so the holder does not tip.

10

Blend a Clay Coil Around the Base Seam of the Candle Holder

4:26
Step 10: Blend a Clay Coil Around the Base Seam of the Candle Holder - How to Make a Clay Candle Holder

Roll one last thin coil and lay it around the seam where the cup meets the base. Blend it up into the cup and down into the base with the spoon tool or your fingers. Finish with any trimming and a final smooth all over. Then let it dry, and paint it or take it to be fired.

Tip

Dry it slowly, loosely covered, so the base does not crack away from the cup.

How to Make a Slab Pottery Dish

Keep going

How to Make a Slab Pottery Dish

Products Used

The Checklist

How to Make a Clay Candle Holder

Tools
4
Materials
3
Steps
10
Video
5 min

Tools we recommend

Your Guide

Crockd

As an Amazon Associate we earn from qualifying purchases. Links on this page may be affiliate links - clicking them and buying doesn't change your price, but helps support Show Me Step by Step.

Tags

Sunday How-To

New pottery tutorials, every Sunday

One short email with the week's best step-by-step guides. Free, no spam, unsubscribe anytime.

Did this work for you?

What's next

Weekly Digest

Liked this pottery tutorial?

Pick the categories you want to hear about. Weekly digest of new step-by-step tutorials. No spam, easy unsubscribe.

Send me tutorials about

We only email about new tutorials. Easy unsubscribe anytime.