{"title":"How to Remove a Stripped Screw","canonicalUrl":"https://www.showmestepbystep.com/home-improvement/how-to-remove-a-stripped-screw","category":{"slug":"home-improvement","name":"Home Improvement"},"creator":{"name":"Ultimate Handyman","channelUrl":"https://www.youtube.com/channel/UC9iG0cCwPrKVGPcaG_K5WHw","sourceVideoUrl":"https://www.youtube.com/watch?v=_mTFQbaT3Zc"},"tldr":"Stripped screw won't budge? Try these 7 methods in order: rubber band, impact driver, extractor bit, Grab-It, center punch, left-handed bit, cold chisel.","totalDurationSeconds":577,"difficulty":"easy","tools":["Cordless drill with reverse","Manual impact driver","Heavy hammer","Damaged screw extractor bit set","Trend Grab-It Pro extractor","Spring-loaded center punch","Left-handed drill bits","Cold chisel","Mole grips or vise-grip pliers"],"materials":["Wide elastic band"],"steps":[{"number":1,"title":"Step 1: Press an elastic band into the screw head","text":"Lay a wide elastic band flat across the stripped screw head. Set your drill to reverse, slot in the correct driver bit, and press the bit straight down through the rubber into the recess. Push hard and squeeze the trigger slowly.The rubber wedges into the chewed-up recess and gives the bit something to bite. It looks too simple to work but it pulls a surprising number of screws straight out. Always try this first because it costs nothing and takes ten seconds."},{"number":2,"title":"Step 2: Shock it loose with a manual impact driver","text":"Slot a quality bit into a manual impact driver and set the rotation collar to loosen. Seat the bit firmly in the damaged head and strike the back of the driver with a heavy hammer.The impact does two things at once. It forces the bit deeper into the recess so it bites better, and it twists the screw a fraction of a turn. That sudden shock often breaks the screw free of whatever it has been seized against. Once it has moved even slightly, you can usually finish the job with a normal drill."},{"number":3,"title":"Step 3: Bite into it with a damaged screw extractor bit","text":"Damaged screw extractor bits have aggressive reverse-cut teeth designed to grip a rounded head. Chuck one in your drill, set the drill to reverse, and press down with real weight behind it.Start the trigger slow until the teeth catch. Once they bite, let the bit do the work. As the teeth dig in further, the screw should start backing out on its own. A basic kit costs around 10 to 15 pounds and pays for itself the first time you use it."},{"number":4,"title":"Step 4: Cut and grip with the Trend Grab-It Pro","text":"The Trend Grab-It is a two-ended bit. Use the cutting end first in reverse to shave a clean recess into the damaged screw head. Then flip it over and drive the extraction end into that fresh recess, again in reverse.Quite often the cutting step alone grips so hard that it backs the screw straight out before you even need to flip the bit. The Grab-It rarely fails on machine screws and even handles wood screws when other extractors give up."},{"number":5,"title":"Step 5: Walk it loose with a spring-loaded center punch","text":"A spring-loaded center punch concentrates a sharp impact onto a tiny point. Set the tip on the outer edge of the screw head, angled so a strike will rotate the screw counter-clockwise.Pull back on the punch to compress the spring, then release. The internal hammer fires forward and drives the tip into the head. Walk the punch around the screw, hitting it again and again. Each strike nudges the screw a fraction of a turn looser. After a handful of hits you can usually grab the head with mole grips or your fingers and finish unscrewing it by hand."},{"number":6,"title":"Step 6: Drill it out with a left-handed drill bit","text":"Left-handed drill bits cut in reverse, which is the same direction that loosens a standard right-hand-thread screw. Pick a bit slightly smaller than the screw head, chuck it in the drill, and set the drill to reverse.Press down firmly and squeeze the trigger. The bit starts cutting into the screw head, but very often it grabs and unscrews the whole fastener before it has a chance to drill all the way through. Best of both worlds: if the screw doesn't come out cleanly, you've still drilled the head off so you can pull the rest of the shank out with pliers."},{"number":7,"title":"Step 7: Knock it round with a cold chisel and hammer","text":"When everything else fails and the head is completely wrecked, grab a cold chisel. Set the cutting edge against the side of the screw head, angled to push it counter-clockwise, and tap the back of the chisel with a hammer.Walk the chisel around the head, knocking the screw loose a fraction at a time. Once the screw spins freely you can pull it the rest of the way with your fingers or a pair of mole grips. This is the last-resort method because it can scar the surrounding material, so save it for when nothing else has worked."}],"recipe":null,"lastUpdated":"2026-05-20T13:32:43.619Z","published":"2026-04-30T14:18:35.910Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}