{"title":"How to Paint a Forest with Acrylics (Beginner Step-by-Step)","canonicalUrl":"https://www.craftingstepbystep.com/painting/how-to-paint-a-forest","category":{"slug":"painting","name":"Painting"},"creator":{"name":"easypeasy art","channelUrl":"https://www.youtube.com/channel/UC0cX4aIglIGw5SbXpDfBoMA","sourceVideoUrl":"https://www.youtube.com/watch?v=v8Gh_VNPFzM"},"tldr":"Beginner acrylic forest tutorial. Layer green base, sunlit center, distant trees, foreground trunks, and stippled leaves for a sunlit pathway landscape.","totalDurationSeconds":539,"difficulty":"easy","tools":["flat brush (1 inch)","round brush (size 4)","round brush (size 6)","fine liner brush (size 0)","fan brush","palette knife","palette or paper plate","water cup","paper towel"],"materials":["stretched canvas (8x10 inch)","titanium white acrylic paint","mars black acrylic paint","sap green acrylic paint","hooker's green acrylic paint","cadmium yellow acrylic paint","yellow ochre acrylic paint","burnt umber acrylic paint"],"steps":[{"number":1,"title":"Step 1: Block In the Green Base","text":"Squeeze out a generous puddle of sap green on your palette. Load a one-inch flat brush and pull broad vertical strokes from the edges of the canvas inward. The strokes don't need to be neat - this layer becomes the deep forest and most of it gets covered later.Leave the center of the canvas lighter than the edges. That bright center is where the sunlight is going to break through the trees. Keep the paint a little thicker on the outside, a little thinner toward the middle."},{"number":2,"title":"Step 2: Blend a Sunlit Center with Yellow","text":"Rinse the brush, then load it with cadmium yellow. Tap the yellow into the still-wet green at the middle of the canvas. Don't paint a sharp shape - dab it on in a loose vertical zone and let it bleed into the surrounding green.Now wipe the brush dry on a paper towel and gently sweep across the seam where yellow meets green. You're not adding more paint, you're softening the edge. The goal is a smooth gradient from bright yellow at the core to deep green at the outside. This becomes the light source that makes the whole forest feel atmospheric."},{"number":3,"title":"Step 3: Sketch the Distant Tree Trunks","text":"Wait until the base layer is dry to the touch. Mix a small amount of burnt umber with a lot of water on the palette - you want a thin wash, not opaque paint. Load a size 4 round brush.Pull thin vertical lines straight up from the bottom of the canvas. Vary the height. Some trunks should reach two-thirds up, some only halfway. Leave gaps between them. These are the trees deepest in the woods, so they should be soft, broken, and faint. If a line looks too dark, dab it back with a damp paper towel."},{"number":4,"title":"Step 4: Add Middle Trees and Start the Dirt Path","text":"Without rinsing, load slightly more burnt umber for a denser line. Paint a second row of trees in front of the background ones - thicker trunks, a bit more defined. Place them so they overlap the lighter background, which immediately creates depth.Now switch to a size 6 round and mix burnt umber with a touch of yellow ochre. Block in a triangular dirt path coming up from the bottom-right corner of the canvas. The wide end is at the bottom edge, the point reaches up into the trees - this is the vanishing point that pulls the viewer's eye into the scene."},{"number":5,"title":"Step 5: Paint the Bold Foreground Trees","text":"Mix burnt umber with a small amount of mars black for the foreground trunks. Load the size 6 round and place a tall, thick tree right at the edge of the canvas - one on each side if you want the framing effect. These trees should run the full height of the canvas and look heavier than anything in the background.Add a few thin branches reaching toward the center of the painting. Use the very tip of the brush and a lighter touch. Branches should taper as they extend, not stay the same thickness. A handful of thin twigs near the canopy sells the foreground perspective."},{"number":6,"title":"Step 6: Build the Dark Foliage Layer","text":"Load a small round brush or a stiff fan brush with hooker's green plus a touch of mars black. Don't smooth it on - stipple. Tap the brush against the canvas in tight clusters. Work along the top third where the canopy lives, and along the edges of the dirt path where bushes grow.This is the deepest layer of leaves. It should feel almost too dark on its own, because the next layer of brighter green is going to sit on top of it. Keep the clusters loose and irregular. Even spacing reads fake."},{"number":7,"title":"Step 7: Layer Medium and Light Green Leaves","text":"Switch to sap green and stipple a second layer of leaves over the dark base. Cover most of the dark green but let some of it peek through at the edges of each leaf cluster - that's how you get the illusion of leaves in front of leaves.Now mix sap green with cadmium yellow for a third pass. Stipple these brighter highlights only where the sunlight would land - right around the bright center of the canvas, on the tops of the leaf clusters facing the light. Three layers of stippling, getting brighter each time, gives the canopy real dimension."},{"number":8,"title":"Step 8: Finish with Grass Tufts and Final Lights","text":"Load a fine liner brush with a mix of sap green and cadmium yellow. Flick tiny upward strokes along the edges of the dirt path. These are grass blades - thin, slightly curved, and clustered in little tufts rather than spread evenly.Step back from the canvas. Look at where your eye lands - that's where the final highlights go. Add one more pass of pure cadmium yellow on the brightest leaves at the center of the canopy and on the brightest grass blades near the path. Sign the corner with a thin brush in burnt umber. You're done."}],"recipe":null,"lastUpdated":"2026-06-08T15:00:08.373Z","published":"2026-06-08T14:59:53.833Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}