{"title":"How to Make an Epoxy River Serving Board","canonicalUrl":"https://www.craftingstepbystep.com/woodworking-crafts/how-to-make-an-epoxy-river-serving-board","category":{"slug":"woodworking-crafts","name":"Woodworking Crafts"},"creator":{"name":"Seth's Custom Creations","channelUrl":"https://www.youtube.com/channel/UCwDHnO9TOPIDHQDFnDh1PRQ","sourceVideoUrl":"https://www.youtube.com/watch?v=7-sbVLuOZ9Y"},"tldr":"Make a teal epoxy river serving board from a wood blank. Cut the river curve, set stones, pour resin, and finish it food-safe. Full step-by-step build.","totalDurationSeconds":393,"difficulty":"advanced","tools":["orbital sander","plunge router","bandsaw","planer","clamps","mixing cups","stir sticks"],"materials":["wood board blank","epoxy resin kit","teal resin pigment","white river stones","painter's tape","sandpaper","food-safe cutting board finish"],"steps":[{"number":1,"title":"Step 1: Mill and Glue Up the Blank","text":"Start with your wood strips and run them through the planer and jointer so every face is flat and square. Glue the strips into one solid panel and clamp it up tight. This is the body of your serving board, so pick clean, dry stock. Let the glue cure fully before you touch it again. A flat, well-glued blank makes every step after this easier."},{"number":2,"title":"Step 2: Draw the River Curve","text":"Sketch an S-shaped line down the length of the panel. That line is where your resin river will run, so play with the curve until it looks right to you. A gentle, flowing bend reads more like a real river than a sharp zigzag. Draw it dark enough to follow at the saw. There is no wrong shape here, so trust your eye and commit to the line."},{"number":3,"title":"Step 3: Cut Along the River Line","text":"Take the panel to the bandsaw and cut right along your drawn curve. This splits the board into two halves that mirror each other. Go slow and let the blade track the line - a smooth cut here means the two pieces line up cleanly later. Once you are through, set the halves side by side so you can see the river gap take shape between them."},{"number":4,"title":"Step 4: Rout the River Channel","text":"Clamp the two halves back together with a gap between them and rout out a recessed valley along the cut. This channel holds the stones and the resin, so keep the depth consistent as you work down the curve. A plunge router with a straight bit does the job well. Steady the base and take light passes rather than trying to hog it all out at once."},{"number":5,"title":"Step 5: Fill the Channel with Stones","text":"Seal the board into a form with painter's tape and a plastic dam so the resin can not leak out. Then lay white river pebbles into the routed channel. Arrange them so they sit below the top surface with room for resin to flow around and over them. The stones give the river depth and texture once the teal epoxy goes in. Pack them loosely, not wall to wall."},{"number":6,"title":"Step 6: Mix and Pour the Teal Epoxy","text":"Mix your epoxy by the ratio on the kit, then stir in teal pigment until the color looks right. Pour it slowly into the channel so it works down through the stones and fills every gap. The resin will find its own level and settle around the pebbles. Pour in stages if the channel is deep, letting each layer set up before adding more. That teal against the light wood is the whole point."},{"number":7,"title":"Step 7: Pour the Clear Flood Coat","text":"Once the river has set, mix a batch of clear epoxy and pour it across the whole board surface. This flood coat seals the wood and gives the top a glassy, level finish. Spread it to the edges so nothing stays dry. Pop any bubbles that rise with a quick pass of heat. Let this coat cure hard before you flip the board or start sanding."},{"number":8,"title":"Step 8: Trim, Sand, and Finish","text":"Rout the excess epoxy off the edges to square the board back up. Then work through the grits with an orbital sander until the whole surface is smooth and even, wood and resin alike. Knock down any sharp edges so the board feels good in the hand. Finish with a food-safe cutting board oil or wax. Wipe it on, let it soak, and buff off the excess."},{"number":9,"title":"Step 9: The Finished River Board","text":"Here is the payoff. The teal river winds through the light striped wood with the white stones frozen inside the glossy resin. Every board comes out one of a kind because no two curves or stone layouts are the same. Wipe it down, and it is ready to serve cheese, bread, or anything else you want to show off on it. Hand-wash only to protect the finish."}],"recipe":null,"lastUpdated":"2026-07-14T00:57:32.895Z","published":"2026-07-14T00:56:34.614Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}