{"title":"How to Make a Slimline Card With Easy Fun Folds","canonicalUrl":"https://www.craftingstepbystep.com/card-making/how-to-make-a-slimline-card","category":{"slug":"card-making","name":"Card Making"},"creator":{"name":"Gerry's Craft Room","channelUrl":"https://www.youtube.com/channel/UC9I_ZjpmicBIlzPLL_zdH6w","sourceVideoUrl":"https://www.youtube.com/watch?v=mCBBldl8MKs"},"tldr":"Make slimline cards from scratch with no special dies. Score double fold, Z fold and gatefold bases, then layer patterned paper scraps.","quickAnswer":"Make slimline cards from scratch with no special dies. An easy project: about 2 hours. Materials cost about $5 to $12. You need 13 things, including A4 or letter cardstock, patterned paper and brown ink pad. The 10 steps start with score the Slimline Card Base at 4 Inches, fold the Slimline Card Base Into a Z Fold, score a Gatefold Slimline Card Base at 2 and 6 Inches and cut Extra Slimline Card Panels From the Leftover Strip.","totalDurationSeconds":764,"videoDurationSeconds":764,"difficulty":"easy","project":{"difficulty":"easy","projectMinutes":120,"waitMinutes":null,"totalMinutes":120,"estimatedCost":{"currency":"USD","min":5,"max":12},"yield":"a set of 6 slimline cards"},"tools":["scoring board","bone folder","paper trimmer","ink blending tool","scissors"],"materials":["A4 or letter cardstock","patterned paper","brown ink pad","script background stamp","liquid glue","double sided tape","foam adhesive squares","die cut frames or sentiments"],"steps":[{"number":1,"title":"Score the Slimline Card Base at 4 Inches","text":"Lay a sheet of cardstock on your scoring board with the long side across the top. Run a bone folder down the groove at 4 inches. Fold along that line and burnish it. Then score again 4 inches from the new fold and fold it the same direction. That gives you the simplest slimline base, a double fold, with three panels about 4 inches wide."},{"number":2,"title":"Fold the Slimline Card Base Into a Z Fold","text":"For a Z fold, score at 4 inches, fold, and score at 4 inches again, the same as the double fold. This time fold the two creases in opposite directions: one panel goes to the back and the other comes to the front. Stand it up and it zigzags. It is one extra fold, but the card looks a lot fancier when it opens."},{"number":3,"title":"Score a Gatefold Slimline Card Base at 2 and 6 Inches","text":"Place a fresh sheet on the scoring board and score at 2 inches, then at 6 inches. Fold both score lines toward the middle. Measure from the 4 inch wide center panel and cut the larger outer flap down to 3 inches. You end up with one small panel, a wide center and a slightly bigger panel on the other side, which closes like a gate."},{"number":4,"title":"Cut Extra Slimline Card Panels From the Leftover Strip","text":"The strip you trimmed off a gatefold is still useful. Cut it into one or two small cards about 4 inches wide. Score one at 1/2 inch along the short side to make a hinge, or leave them flat as separate panels. Gerry glues these on top of the larger bases later to add another layer. It is an easy way to use every scrap of the sheet."},{"number":5,"title":"Trim Patterned Paper Mats for the Slimline Card Panels","text":"Measure each panel on your card bases. Cut a piece of patterned paper for each one, a little over 1/4 inch smaller in both directions. That leaves a thin border of cardstock showing around every mat. Keep the measurement the same on every panel so the borders match. Set the mats beside the card they belong to so you do not mix them up."},{"number":6,"title":"Ink the Edges of the Slimline Card Patterned Paper","text":"Tap a round blending tool onto a brown ink pad. Hold a patterned mat flat and rub the tool along the edge in small circles, working from the table onto the paper. Go all the way around. The edge darkens a little and the mat looks finished instead of freshly cut. Gerry uses walnut brown for a vintage feel, but any color from your paper works."},{"number":7,"title":"Add Texture to the Light Slimline Card Base With Ink","text":"Pale cardstock can look flat next to busy patterned paper. Blend a little ink around the edges of the light base. Then load a script stamp lightly and press it here and there, turning the paper and the stamp so the writing runs in different directions. Only stamp where the cardstock will show around the mats. The rest gets covered anyway."},{"number":8,"title":"Glue the Patterned Paper Panels on the Slimline Card","text":"Spread liquid glue on the back of each mat and press it onto its panel, centered so the border is even. Liquid glue gives you a few seconds to slide it straight. Lay each panel flat while it dries. If part of a pattern lands somewhere you do not like, cover it with a strip of a different scrap. That hides it and adds interest at the same time."},{"number":9,"title":"Layer Scraps and a Sentiment on the Slimline Card","text":"Gather leftover strips and cut bits of patterned paper. Lay them on the card in a loose cluster and move them around until you like the balance. A thin black strip helps lighter papers pop. Glue the pieces down, then add a framed sentiment over the top. Gerry ties hers to the theme with oval and tag shaped frames."},{"number":10,"title":"Add a Raised Frame Focal Point to the Slimline Card","text":"Stick foam squares on the back of a die cut frame or a fussy cut flower. Line it up over your scrap cluster and press it down so it sits a little higher than the layers behind it. That small lift gives the card depth. For a softer lift, fold a strip of double sided tape over on itself a few times and use it as a thin spacer."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-20T15:13:10.213Z","published":"2026-11-20T15:13:09.906Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}