{"title":"How to Make a Macrame Wreath (Easy Mandala Ring)","canonicalUrl":"https://www.craftingstepbystep.com/macrame/how-to-make-a-macrame-wreath","category":{"slug":"macrame","name":"Macramé"},"creator":{"name":"Melanie Ham","channelUrl":"https://www.youtube.com/channel/UCXrEE1TyCslZgsH1Pql51-Q","sourceVideoUrl":"https://www.youtube.com/watch?v=TRv6Fh6jnGw"},"tldr":"Make a macrame mandala wreath on a metal ring with square knots and half hitches, wood beads and a brushed fringe. Step by step for beginners.","quickAnswer":"Make a macrame mandala wreath on a metal ring with square knots and half hitches, wood beads and a brushed fringe. A medium project: about 2 hours 30 minutes. Materials cost about $8 to $18. You need 8 things, including 3-4mm twisted cotton macrame cord, 10-inch metal ring and wood beads. The 9 steps start with gather the Macrame Cord, Metal Ring and Beads, tie Lark's Head Knots Onto the Macrame Wreath Ring and tie the First Row of Macrame Square Knots.","totalDurationSeconds":748,"videoDurationSeconds":748,"difficulty":"medium","project":{"difficulty":"medium","projectMinutes":150,"waitMinutes":null,"totalMinutes":150,"estimatedCost":{"currency":"USD","min":8,"max":18},"yield":"1 wreath"},"tools":["sharp scissors","fabric scissors","tapestry needle","pet slicker brush","measuring tape"],"materials":["3-4mm twisted cotton macrame cord","10-inch metal ring","wood beads"],"steps":[{"number":1,"title":"Gather the Macrame Cord, Metal Ring and Beads","text":"Get out your twisted cotton cord, a 10 inch metal ring, ten wood beads, sharp scissors and a pet slicker brush. Cut the cord into 24 inch lengths. Each unit of the wreath uses eight cords and there are ten units, so you need 80 pieces. Cut them all at once and keep them in a bundle. The beads are optional if you prefer a plain look."},{"number":2,"title":"Tie Lark's Head Knots Onto the Macrame Wreath Ring","text":"Fold a cord in half to make a loop. Lay the loop over the front of the ring, then bring the two tails down through it and pull snug. That is a lark's head knot. Add eight cords side by side for one unit, which gives you 16 strands. You can work flat on a table, or hang the ring from a drawer pull or a cabinet knob."},{"number":3,"title":"Tie the First Row of Macrame Square Knots","text":"Leave the two outer strands on each side alone for now. Take the middle four strands. Cross the right strand over the two center strands, lay the left strand over it, then pass the left strand behind and up through the loop. Tighten, then repeat in the opposite direction. That is one square knot. Tie two more beside it so the row has three."},{"number":4,"title":"Add Offset Square Knots to Shape the Triangle","text":"For the second row, take the right two strands from one knot and the left two from its neighbor, and tie a square knot between them. Do this in both gaps so the row has two knots sitting offset. Then take the center four strands and tie one last square knot below them. You now have a small triangle of six square knots hanging from the ring."},{"number":5,"title":"Tie Double Half Hitches Along the Triangle Edge","text":"Bring in the outer strands you left aside. Take the far right strand as your lead cord and hold it at an angle along the edge of the triangle. Wrap the next strand over and around it twice and pull up to tighten. Keep going down the edge, one strand at a time, until you reach the center. Then do the same from the left side."},{"number":6,"title":"Work a Second Round of Half Hitches for the Border","text":"Close the point where the two sides meet by tying one lead cord around the other. Then pick up the next strand as a new lead cord and run a second round of double half hitches down each side, tight under the first. Press the strands together with your fingers if they start to spread. Leave the two lead cords hanging at the center when you finish."},{"number":7,"title":"Add a Wood Bead Below the Macrame Unit","text":"Thread one center lead cord through a tapestry needle and push it through the hole of a wood bead, then do the same with the other. Slide the bead up tight under the point of the unit. Tie the two cords together in a single knot right under the bead to hold it. If you skip the bead, tie the two lead cords around each other to close the point."},{"number":8,"title":"Unravel and Brush Out the Macrame Fringe","text":"Cut all the strands at the bottom to about 3/4 inch with ordinary scissors. Then use the tapestry needle to pull apart the twists on each strand so the plies separate. Once they are loose, comb the fringe with a pet slicker brush. It turns the cord into a soft, fluffy fringe in a few strokes. Leave it unbrushed if you prefer a rope look."},{"number":9,"title":"Trim the Fringe and Repeat Around the Wreath Ring","text":"Brushing makes the fringe a bit ragged, so trim it again with sharp fabric scissors for a crisp, even edge. Match the length to your other units. Then slide the finished unit to one side, tie on eight more cords right next to it and repeat steps 2 to 9. Ten units fill a 10 inch ring all the way around."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-22T15:01:26.977Z","published":"2026-11-22T15:01:26.697Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}