{"title":"How to Make a Gift Card Holder From 6x6 Paper","canonicalUrl":"https://www.craftingstepbystep.com/card-making/how-to-make-a-gift-card-holder","category":{"slug":"card-making","name":"Card Making"},"creator":{"name":"4Holidays Designs","channelUrl":"https://www.youtube.com/channel/UC7zk-jrRlwpXJpUAJ_BgwxQ","sourceVideoUrl":"https://www.youtube.com/watch?v=aqaoz_r_gXc"},"tldr":"Make a gift card holder from 6x6 paper with exact measurements. Score, fold and glue a pocket, then finish it with a ribbon belly band and bow.","quickAnswer":"Make a gift card holder from 6x6 paper with exact measurements. An easy project. You need 13 things, including 6x6 cardstock for the base, 6x6 patterned paper and liquid craft glue. The 10 steps start with trim the Gift Card Holder Base to 5 1/4 by 6 Inches, score the Gift Card Holder Base on a Scoring Board, snip the Corner Squares Out of the Scored Base and round the Corners of the Gift Card Holder Base.","totalDurationSeconds":989,"videoDurationSeconds":989,"difficulty":"easy","project":{"difficulty":"easy","projectMinutes":null,"waitMinutes":null,"totalMinutes":null,"estimatedCost":null,"yield":null},"tools":["paper trimmer","scoring board","bone folder","scissors","corner rounder punch","circle punch","hot glue gun"],"materials":["6x6 cardstock for the base","6x6 patterned paper","liquid craft glue","3/8 inch satin ribbon","small Christmas charm","thin craft wire"],"steps":[{"number":1,"title":"Trim the Gift Card Holder Base to 5 1/4 by 6 Inches","text":"Pick a solid sheet from your 6x6 pad for the base. Jennifer uses green so the score lines are easy to see on camera. Slide it into a paper trimmer and cut one side down to 5 1/4 inches, leaving the other side at 6 inches. Set your patterned sheet aside for now. You will cut it down later."},{"number":2,"title":"Score the Gift Card Holder Base on a Scoring Board","text":"Lay the 5 1/4 inch side along the top of a scoring board. Score at 3/4 inch, turn the paper around and score at 3/4 inch again. Then turn it so the 6 inch side runs along the top and score at 1 1/4 and 3 3/4 inches. Two light passes with the bone folder are better than one hard one."},{"number":3,"title":"Snip the Corner Squares Out of the Scored Base","text":"Where the score lines cross, you have four small squares, one in each corner. Mark each one with a small X so you know what to remove. Cut along the score lines with sharp scissors to take the four squares out, the same way you would for a small box. Then trim the corners of the inside flap at a slight angle so it folds in smoothly."},{"number":4,"title":"Round the Corners of the Gift Card Holder Base","text":"This is optional, but rounded corners make the finished holder look softer and more finished. Slide each outer corner into a corner rounder punch and press down. Jennifer uses a 3 in 1 punch and picks one of the gentler curves. Do the same on the patterned sheet once you cut it, so both layers match."},{"number":5,"title":"Glue the Plaid Paper Layer Onto the Gift Card Holder","text":"Cut your patterned paper to about 3 1/2 by 5 3/4 inches and round its corners. Fold and burnish the base along the long score line. Spread liquid glue on the outside panel of the base, then lay the plaid on top. Eyeball it so a thin border of the base shows around the edge. Let it set for a minute before you move on."},{"number":6,"title":"Crease the Fold Through the Plaid and Base With a Ruler","text":"The patterned layer covers the fold, so it has no score line of its own. Lay a ruler along the fold, bend the paper over it and press. This stretches both layers together, the same trick used in mini albums. Once it is folded, run a bone folder along the crease to make it sharp."},{"number":7,"title":"Punch a Thumb Notch in the Gift Card Holder Front","text":"Slide the top edge of the front panel into a circle punch so only a sliver of the circle overlaps the paper. Press down to cut a small half-moon notch. That notch lets the person who opens it pull the gift card out with a thumb. Any size circle punch is fine."},{"number":8,"title":"Glue the Side Flaps of the Gift Card Holder Pocket","text":"Fold in the two narrow side flaps. Run a line of liquid glue along each one, stopping where the flap edge stops being straight. Fold the bottom panel up over the flaps and press it down. You now have a small pocket. Slide a gift card in to check the fit while the glue is still a little soft."},{"number":9,"title":"Wrap a Ribbon Belly Band Around the Gift Card Holder","text":"Cut a narrow strip of the solid paper for a belly band. Glue a length of ribbon down the center of it. Wrap the band around the holder, fold it to fit and crease each corner. Glue the ends together on the front, where the bow will hide the seam. Keep it loose enough that the card can still slide out."},{"number":10,"title":"Tie a Red Satin Bow on the Gift Card Holder Belly Band","text":"Tie a small double bow from the same ribbon. Jennifer threads a little Christmas charm onto a short piece of wire, then twists the wire around the center of the bow to hold it. Put a dab of hot glue on the belly band seam and press the bow on top. Slide the band onto the holder and tuck the gift card inside."}],"commonProblems":[],"recipe":null,"lastUpdated":"2026-11-20T14:58:31.545Z","published":"2026-11-20T14:58:31.241Z","license":"CC BY 4.0. Credit Show Me Step by Step with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure. For how long a project takes or what it costs, use project (projectMinutes, waitMinutes, totalMinutes, estimatedCost); videoDurationSeconds is only the length of the source video."}