{"title":"How to Make a Concrete Air Plant Holder","canonicalUrl":"https://www.craftingstepbystep.com/crafts/how-to-make-a-concrete-air-plant-holder","category":{"slug":"crafts","name":"Crafts"},"creator":{"name":"Meg's Cozy Cottage","channelUrl":"https://www.youtube.com/channel/UCY4muUqNKvwclvaiDtxGSeg","sourceVideoUrl":"https://www.youtube.com/watch?v=7ZUMwVwoqqg"},"tldr":"Make a modern concrete air plant holder with a gold-dipped edge and a gold wire nest. Cast, demold, spray, and seat a Tillandsia. Easy weekend DIY.","totalDurationSeconds":241,"difficulty":"easy","tools":["mixing bucket or container","paint stir stick","two small plastic grower pots (molds)","wood skewers","sandpaper","needle-nose pliers","gloves"],"materials":["concrete or cement mix","water","cooking spray or mold release","construction paper","painter's or scotch tape","metallic gold spray paint","E6000 craft glue","14-gauge gold wire","air plant (Tillandsia)"],"steps":[{"number":1,"title":"Step 1: Mix the Concrete","text":"Mix your concrete in a bucket following the ratio printed on the bag. Megan uses a quick-set concrete she had on hand and adds a splash of extra water so the mix pours a little runnier. A looser mix fills small molds cleanly and settles into the corners instead of leaving voids.Stir with a paint stick until there are no dry pockets and it looks like thick oatmeal. Do not go too soupy or the block ends up weak. You want it pourable but still holding its shape on the stick."},{"number":2,"title":"Step 2: Fill the Molds and Set the Skewers","text":"Scoop the wet concrete into two small plastic grower pots. These are your molds, and the tapered shape pops the finished block out easily. Pack the concrete down hard with the paint stick so it fills the bottom and edges.Push a couple of wood skewers straight down into the center of each pot. They hold open a channel you will glue the wire into later. Tamp everything down again, then tap the pots on the table a few times to bring any trapped air bubbles up to the surface."},{"number":3,"title":"Step 3: Demold and Sand","text":"When the concrete is about halfway set, pull the skewers straight out. Wait too long and they lock in, so a firm tug at the halfway point saves you from digging them out with pliers later. Let the blocks finish curing fully before you unmold.To release each block, tap the bottom of the plastic pot with a hammer until the concrete slides free. Run a scrap of sandpaper over the edges to knock off the sharp lip and any rough grit from the mold. Sand lightly for a crisp look or harder for a soft, distressed stone finish."},{"number":4,"title":"Step 4: Mask a Torn Gold Line","text":"Tear a piece of construction paper so it has a rough, ragged edge instead of a clean straight cut. That torn line is what gives the gold its organic, hand-made look once you spray. Do not aim for anything perfect here.Wrap the paper around a block and tape it in place, leaving bare only the strip of concrete you want to turn gold. Megan does one holder with the gold band up near the top and the other with it down at the bottom, so the finished pair looks intentional rather than identical."},{"number":5,"title":"Step 5: Spray the Gold","text":"Take the masked blocks somewhere with airflow and spray the exposed concrete with metallic gold paint. Hold the can back a few inches and keep it moving so the paint lands as an even mist, not a puddle. Two or three light coats beat one heavy one.Check for bare spots along the torn edge and touch them up before the paint sets. Then leave the blocks alone for about half an hour, just long enough for the gold to dry to the touch."},{"number":6,"title":"Step 6: Glue in the Wire","text":"Peel off the paper once the paint is dry and check that you like the gold line on both blocks. Now for the part that turns a block into a holder. Squeeze E6000 craft glue into the channel the skewer left behind in the top of each one.Push a length of 14-gauge gold wire down into the glued hole so it stands up straight. Do not shape it yet. Just anchor it and prop the loose end against something steady while the glue expands and grabs. E6000 needs time to cure, so walk away and let it set."},{"number":7,"title":"Step 7: Shape the Nest and Add the Air Plant","text":"With the glue cured, bend the free wire into an open nest or spiral that will cradle the air plant. Hold your Tillandsia against the wire as you shape it so the nest ends up sized to the plant, snug enough to hold it but open enough that air still gets to the base.Use needle-nose pliers for the tight coils on the smaller holder and just your hands for the looser shape on the bigger one. Set the air plant into the finished nest and you are done. Two little concrete holders, ready for a shelf or to give away."}],"recipe":null,"lastUpdated":"2026-07-22T15:38:50.246Z","published":"2026-07-22T15:38:45.878Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}