{"title":"How to Install an Electric Water Heater","canonicalUrl":"https://www.showmestepbystep.com/home-improvement/how-to-install-a-water-heater","category":{"slug":"home-improvement","name":"Home Improvement"},"creator":{"name":"The Home Depot","channelUrl":"https://www.youtube.com/channel/UCfB9yx0y0dUwQ0lpjH8R4gA","sourceVideoUrl":"https://www.youtube.com/watch?v=t_7Esvyx6S4"},"tldr":"Replace an electric water heater yourself. Shut off power and water, drain the old tank, connect the water lines, wire it up, and check for leaks.","totalDurationSeconds":370,"difficulty":"advanced","tools":["pipe wrench","non-contact voltage tester","adjustable wrench","screwdriver","torpedo level","garden hose"],"materials":["electric water heater","flexible water connectors","Teflon tape","wire connectors","drain pan","temperature and pressure relief valve","discharge pipe"],"steps":[{"number":1,"title":"Step 1: Cut the Power and Water, Then Drain the Old Tank","text":"Head to the main panel and shut off the breaker feeding the water heater. Remove any fuses too. Then close the cold-water shutoff valve on the line above the tank. In the video it's labeled right on the wall, which is a smart move if you ever need to find it fast. Hook a garden hose to the drain valve at the bottom, run it to a floor drain, and open a hot faucet somewhere in the house so the tank empties instead of holding a vacuum."},{"number":2,"title":"Step 2: Disconnect and Remove the Old Heater","text":"With the tank empty and the power off, pull the cover on the electrical junction at the top and disconnect the wires. Loosen the flex conduit connector and free the cable. Then unthread the hot and cold water connectors with a pipe wrench. Once everything is loose, the old tank is free to roll out of the way. It's lighter now that it's drained, but it can still be awkward, so take your time getting it clear of the space."},{"number":3,"title":"Step 3: Set the New Tank on a Drain Pan and Level It","text":"Slide a drain pan into position and set the new tank on top of it. The pan catches drips and small leaks so they don't end up on your floor. Now put a torpedo level across the top and check side to side. A tank that sits level heats evenly and puts less strain on the connections. Shim under the base if it rocks or leans. Get this right before you start plumbing, because moving a connected tank is no fun."},{"number":4,"title":"Step 4: Wrap the Fittings with Teflon Tape","text":"Before you connect any water lines, wrap the threaded nipples with Teflon tape. A few turns in the direction the fitting tightens gives you a clean, leak-free seal. The installer in the video uses color-coded dielectric nipples, blue for cold and red for hot, which also protects against corrosion where copper meets steel. Keep the tape snug and even, and don't run it over the very first thread so nothing shreds into the line."},{"number":5,"title":"Step 5: Connect and Tighten the Water Lines","text":"Now bring the hot and cold lines to the tank. Flexible water connectors make this a lot easier than trying to fit rigid copper into a tight spot, and they let you nudge the tank without stressing the joints. Thread each connector onto its port and snug it down with a wrench. Don't crank on it. Firm and snug is enough, and overtightening can crack a fitting. Match hot to hot and cold to cold, which the color coding makes easy to track."},{"number":6,"title":"Step 6: Wire the Electrical Connections","text":"Double-check the breaker is still off and touch a voltage tester to the wires to confirm no power is present. Feed the cable through the connector on top of the tank and land the wires. Match the colors to the tank's leads and secure them with wire connectors. Don't skip the ground. Fasten the bare or green wire to the green ground screw. A solid ground is what keeps the tank safe if a wire ever works loose inside."},{"number":7,"title":"Step 7: Install the T&P Relief Valve and Discharge Pipe","text":"The temperature and pressure relief valve is the tank's safety release. Wrap its threads with tape and screw it into the port on the tank. Then run a discharge pipe from the valve down to within a few inches of the floor. That pipe carries hot water safely down and away if the valve ever opens, instead of spraying out at eye level. This part isn't optional. Code requires it, and it's the piece that keeps a failing tank from becoming a hazard."},{"number":8,"title":"Step 8: Fill the Tank, Then Restore Power and Check for Leaks","text":"Open the cold-water valve and let the tank fill. Keep a hot faucet open somewhere in the house so trapped air can push out. When water runs steady and smooth with no sputtering, the tank is full and the air is purged. Now, and only now, go back to the panel and switch the breaker on. Walk the connections one more time and look for drips at every fitting. A tank that's still bone dry after 20 minutes of heating is a job well done. If you liked this, our guide to installing a dishwasher is a good next project."}],"recipe":null,"lastUpdated":"2026-07-12T23:20:08.510Z","published":"2026-07-12T23:18:38.730Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}