{"title":"How to Install a Toilet in 7 Steps","canonicalUrl":"https://www.showmestepbystep.com/home-improvement/how-to-install-a-toilet","category":{"slug":"home-improvement","name":"Home Improvement"},"creator":{"name":"The Excellent Laborer","channelUrl":"https://www.youtube.com/channel/UCUJXaEduMHGB3Iap3DusmAA","sourceVideoUrl":"https://www.youtube.com/watch?v=9tvEMbwRWB4"},"tldr":"How to install a toilet step by step. Prep the water line, set the wax ring, bolt the bowl down, connect supply, leak-check, and caulk. No plumber needed.","totalDurationSeconds":884,"difficulty":"medium","tools":["adjustable crescent wrench","ratchet pipe cutter","hacksaw","tape measure","pencil","hammer","pliers","screwdriver","level","damp rag"],"materials":["toilet (Kohler or similar)","wax ring with bolts","toilet supply line (3/8 inch)","SharkBite 1/2 inch shutoff valve","100% silicone caulk","pipe cover (optional)"],"steps":[{"number":1,"title":"Step 1: Gather Your Tools and Shut Off the Water","text":"Before you touch the existing toilet, lay everything out where you can see it. You will want a new wax ring (or a wax-free Korky equivalent), a new flexible supply line, fresh closet bolts, 100% silicone caulk and a caulk gun, an adjustable wrench, channel-lock pliers, a putty knife to scrape the old wax, a tape measure, and a few clean rags. Watch at 0:20 for the full kit Excellent Laborer lays out.Then shut the water off at the angle stop behind the toilet, flush, hold the handle down, and sponge the remaining water out of the tank and bowl. Disconnect the supply line from the tank with the adjustable wrench. Your bowl is now empty and you are ready to remove the old toilet."},{"number":2,"title":"Step 2: Prep the Closet Flange","text":"The closet flange is the white ring on the floor that the toilet bolts to. If you're replacing an old toilet, scrape the old wax off the flange with a putty knife and pull the old bolts out. On a new build like the one in the video, you'll need to hold the lip of the knockout plug with pliers, then tap it loose with a hammer. Watch at 3:35. Get the bulk of the plug out so it doesn't fall down the drain and clog the line."},{"number":3,"title":"Step 3: Set the Closet Bolts in the Flange","text":"The new bolts slide into the slots on the flange. Drop each bolt in head-down, then twist the foot so it locks sideways and won't slip out when you tighten things up. Slide the plastic retainer caps down the bolt threads so the bolts stay upright while you lower the toilet on. Watch at 5:40. Measure the distance between the two bolts and the back wall to make sure they're equidistant. About 11 and 7/8 inches from the wall is typical for a standard 12-inch rough-in."},{"number":4,"title":"Step 4: Press On the Wax Ring","text":"Lay the toilet on its side on a piece of cardboard so you don't scratch the porcelain. Take the wax ring out of the box and press the wax side firmly onto the bottom of the toilet, centered over the drain horn. Watch at 6:25. The plastic funnel (if your ring has one) should point down and away from the toilet so it can drop into the flange when you set the bowl. Work the wax in evenly around the opening so the seal is uniform on all sides."},{"number":5,"title":"Step 5: Lower the Toilet and Tighten the Bolts","text":"Pick the toilet up by the bowl rim and lower it straight down so the two closet bolts thread through the holes in the base. Don't drag it sideways or you'll smear the wax. Press the bowl down with your body weight so the wax compresses against the flange and the porcelain sits flat on the floor. Watch at 8:00. Add the washer and nut to each bolt, hand-tighten, then snug them down with a crescent wrench. Alternate sides so the toilet pulls down evenly. Stop when the nut is firm. Cranking past that point cracks the porcelain or the flange."},{"number":6,"title":"Step 6: Install the Tank and Connect the Supply Line","text":"Wipe the rubber gaskets on the underside of the tank with the damp rag so no grit sits between the tank and bowl. Set the tank down with the bolts dropping through the holes in the bowl, then add a washer and nut on each bolt from inside the tank and tighten them in a star pattern. Now hand-thread one end of the supply line onto the toilet's fill valve and the other end onto the shutoff. Watch at 11:10. Snug both ends with a crescent wrench, but only a quarter turn past hand-tight. Over-cranking strips the brass."},{"number":7,"title":"Step 7: Turn On the Water, Test, and Caulk","text":"Open the angle valve slowly and let the tank fill. Watch the supply connection, the tank-to-bowl gaskets, and the base of the toilet for any sign of water. Flush twice and feel around the floor with your hand to confirm everything is dry. Watch at 14:05. Run a thin bead of 100% silicone caulk around the front and sides of the toilet base, but leave a small gap at the back. If the wax ring ever fails, that gap lets water escape so you'll see it before it rots the subfloor."}],"recipe":null,"lastUpdated":"2026-05-20T13:36:20.849Z","published":"2026-05-14T14:42:32.354Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}