{"title":"How to Install a Garbage Disposal - 7-Step Sink Plumbing Guide","canonicalUrl":"https://www.showmestepbystep.com/home-improvement/how-to-install-a-garbage-disposal","category":{"slug":"home-improvement","name":"Home Improvement"},"creator":{"name":"ToolRev","channelUrl":"https://www.youtube.com/channel/UC5uWnYudXmGlTlR45xrpHiw","sourceVideoUrl":"https://www.youtube.com/watch?v=lhyglazl_oo"},"tldr":"Install a garbage disposal yourself in 7 steps. Disassemble the flange, apply plumber's putty, mount the disposal, attach the P-trap, and check for leaks.","totalDurationSeconds":487,"difficulty":"medium","tools":["Flathead screwdriver","Phillips screwdriver","Adjustable wrench or channel-lock pliers","Hacksaw or PVC cutter (for trimming the wall tube)","Bucket or towel for under-sink water","Work gloves","Headlamp or flashlight"],"materials":["Garbage disposal unit (ring-mount style; 1/2-HP minimum for most kitchens)","Plumber's putty","P-trap kit (with slip nuts and washers)","Power cord with strain relief (if not pre-installed on the new disposal)","Teflon tape (for any threaded connections)","Wire nuts and electrical tape (for hard-wired installs)"],"steps":[{"number":1,"title":"Step 1: Lay Out the Parts and Verify What You Have","text":"A ring-mount disposal ships with the sink-flange assembly (the silver ring you'll see in the sink), three mounting screws, a snap ring, a fiber gasket, and a discharge tube with rubber gasket. The disposal body itself has the motor and grinding chamber inside.Check whether the disposal comes with a pre-installed power cord. Many do, but not all - if yours doesn't, you'll need to wire one on from a hardware store kit (about $10) or hard-wire it to a switched circuit. If you're swapping an old disposal, the existing power cord typically works on the new unit - follow the new manual's wiring diagram.You'll also need a P-trap kit from the hardware store. The P-trap is the curved pipe that connects the disposal's drain to the wall stub-out. Don't reuse a corroded old P-trap."},{"number":2,"title":"Step 2: Disassemble the Sink Flange Assembly","text":"Before you can install the flange into the sink, you need to break the assembly into its pieces. Back the three mounting screws out all the way - they're on the underside of the upper mounting ring.With the screws out, use a flathead screwdriver to pop the snap ring off. The snap ring is a black retaining clip that holds the upper ring against the flange. Lift the upper mounting ring and fiber gasket away. The sink flange (the silver piece that goes into the drain hole from the top) should now be free."},{"number":3,"title":"Step 3: Apply Plumber's Putty to the Sink Flange","text":"Plumber's putty creates the water seal between the flange and the sink. Roll a small amount of putty into a rope about the diameter of a pencil. Wrap the rope around the bottom edge of the sink flange in a complete ring.From above the sink, drop the flange into the drain hole and press it down firmly. Excess putty will squish out around the edges - leave it for now, you'll wipe it clean once the flange is bolted in.Line up the flange so any branding or logos face the way you want before you commit. Once the putty seats it's harder to rotate."},{"number":4,"title":"Step 4: Mount the Flange from Below and Tighten Evenly","text":"Get under the sink. Slide the fiber gasket up onto the bottom of the flange, then the upper mounting ring on top of that. Hold them in place with one hand while you snap the retaining ring on with the included plastic tool (or a screwdriver).Now tighten the three mounting screws. The trick here is to tighten them EVENLY - go around in a star pattern, a quarter-turn at a time on each, rather than running one screw all the way down and then moving to the next. Even pressure means the flange seats flat instead of warping.Stop tightening when you see the flange firmly contact the sink and putty squeezes out around the edges. If you start to see the flange bend or bow, you've gone too far - back off a quarter turn."},{"number":5,"title":"Step 5: Attach the Discharge Tube to the Disposal","text":"The discharge tube is the 1.5-inch elbow with the rubber gasket that carries waste water out of the disposal. Position the rubber gasket onto the disposal's side outlet, then bolt the discharge tube on with the included bracket and two screws.Tighten until the rubber washer compresses enough to form a water seal - usually two or three full turns past finger-tight. Over-tightening crushes the rubber and ruins the seal, so stop when the washer is firm against the metal.Slide the slip nut and slip washer onto the free end of the discharge tube. You'll connect those to the P-trap once the disposal is mounted on the sink."},{"number":6,"title":"Step 6: Mount the Disposal onto the Sink Flange","text":"Now the heavy part. The disposal's lower ring has three tabs that engage three matching ramps on the upper ring you installed under the sink. Lift the disposal straight up (it's heavy - support it with both hands or a knee) and align the tabs with the ramps.Once the tabs touch the ramps, twist the disposal clockwise. The tabs ride up the ramps and lock the disposal in place. You can use the wrench that came in the box, but if the rings are clean it usually goes on hand-tight.The disposal will still rotate after locking, which is intentional - it lets you aim the discharge tube toward your existing plumbing without removing the whole unit."},{"number":7,"title":"Step 7: Connect the P-Trap and Check for Leaks","text":"The P-trap connects the disposal's discharge tube to the wall stub-out. Hold the P-trap up to see where it needs to land - the curved section sits below the disposal, and the straight section runs to the wall.Cut the wall tube (the straight piece that slides into the wall stub-out) down so it doesn't extend past the wall opening. A hacksaw or PVC cutter does this cleanly. Deburr the cut edge with a knife or sandpaper so it slides smoothly through the slip nut.Slide the slip nuts and washers into position and hand-tighten. A wrench is overkill for these plastic fittings - it cracks the threads. Once everything is connected, run hot and cold water through the sink for 30 seconds, then look under every joint with a paper towel. Any moisture means tighten that nut a quarter turn. No moisture means you're done."}],"recipe":null,"lastUpdated":"2026-05-20T13:33:27.320Z","published":"2026-05-11T15:38:46.097Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}