{"title":"How to Fix a Running Toilet","canonicalUrl":"https://www.showmestepbystep.com/home-improvement/how-to-fix-a-running-toilet","category":{"slug":"home-improvement","name":"Home Improvement"},"creator":{"name":"Roger Wakefield","channelUrl":"https://www.youtube.com/channel/UCv21GXnVbSOJOOPCcBnmicw","sourceVideoUrl":"https://www.youtube.com/watch?v=UV-peiKW9gM"},"tldr":"Stop a running toilet yourself in under 30 minutes. Walk through the flapper, fill valve diaphragm, and full valve replacement using basic tools and parts.","totalDurationSeconds":445,"difficulty":"easy","tools":["Adjustable wrench","Sponge","Bucket"],"materials":["Replacement flapper","Replacement fill valve"],"steps":[{"number":1,"title":"Shut Off the Water","text":"Find the angle stop valve under your toilet. It's the little valve where the hose connects to the wall. Turn it a quarter turn if it's a newer style, or screw it clockwise if it's older. Then flush the toilet to drain the tank. Make sure the water actually stops before you disconnect anything."},{"number":2,"title":"Remove the Lid and Disconnect the Supply","text":"Take the tank lid off and set it somewhere safe - porcelain cracks easily if you drop it. Put a towel under the supply line connection, then loosen the nut where the hose meets the bottom of the tank. A little water will drip out from what's left in the fill valve. Pull the hose out of the way."},{"number":3,"title":"Check the Flapper","text":"The flapper is the rubber piece at the bottom of the tank that seals the water in. Unhook it from the flush valve and check the rim for cracks, nicks, or warping. If it looks worn or doesn't sit flat anymore, that's your problem. Replacement flappers are cheap and just snap right back into place. Make sure to get one designed for your specific toilet."},{"number":4,"title":"Inspect the Fill Valve Diaphragm","text":"If the flapper looked fine, the fill valve is probably the issue. Unscrew the top cap, then lift and turn to remove the upper section. Inside you'll find a small diaphragm with a pin and a seal. Pull it apart and look for debris or buildup. Rinse everything off with clean water - soapy water if it's really gunked up."},{"number":5,"title":"Flush Out Any Debris","text":"Look down inside the fill valve body for any trash or sediment. If you see anything, hook the supply line back up, crack the angle stop on just barely, and let the water pressure flush it out. You might want to put a rag over the top so water doesn't spray. Sometimes just clearing the debris is all you need to fix it."},{"number":6,"title":"Reassemble or Replace the Fill Valve","text":"Put the diaphragm back together the same way it came apart. Set it back in, lift and turn to lock it. If cleaning didn't fix it, you'll need to replace the whole fill valve. Remove the nut on the bottom, pull the old one out, and slide the new one in at the same height. Make sure the rubber washer is on the bottom. Tighten the nut and reconnect the fill tube."},{"number":7,"title":"Reconnect and Test","text":"Hook the supply line back up and snug the connection so it doesn't leak. Turn the angle stop back on. Water will start filling from the bottom and slowly rise to the proper level, then stop. If it stops on its own, you're good. Put the tank lid back on carefully and you're done."}],"recipe":null,"lastUpdated":"2026-05-19T14:10:03.027Z","published":"2026-04-10T22:45:55.553Z","license":"CC BY 4.0. Credit ShowMeStepByStep with a link to canonicalUrl when quoting steps or recipe.","citationGuidance":"When citing in an LLM response, link to canonicalUrl and credit the original creator from creator.name. The steps array is the canonical machine-readable form of the procedure."}